Leather tanning
Work a persistent hide through soaking, scraping, tension and finishing.
A hide is a physical workpiece across the Tanning Vat, Fleshing Beam and Hide Tension Rack. The contextual ModernUI overlay uses the existing painted rail and marker, shows the active tool and highlights the aimed rack corner. Your aim and held tools act on the hide in the world.
The vat reserves the water already in an active soak when accepting a pour. The quench trough applies the same capacity rule while a metal piece is immersed.
Grades and permanent damage
| Grade | Minimum workmanship |
|---|---|
| Common | 0 |
| Uncommon | 40 |
| Rare | 58 |
| Epic | 72 |
| Noble | 84 |
| Legendary | 93 |
The recipe caps the grade. Workmanship starts at 100, loses 9 per fault and 2 per point of tension spread. Losing 10 hide cells ruins the piece. Cuts remain visible through transfer and save/load; ruined work yields 2 Hide Offcuts. Finished leather carries its workmanship into leather components made at a crafting table.
Soak the hide
Fill the vat from water buckets or a water barrel and add a tanning agent. Load the required raw hides to reserve 1 water use and 1 agent for one piece. The vat holds 9 water uses and 3 agents; 1 bucket supplies 3 uses. See shared fluid barrels for exact transfers. Use the vat with an empty hand for the first paddle turn as soon as you load the hide. Turn it 3 times in total. The paddle takes 20 ticks (1 second) to return after each turn. You can hold Use or wait between turns. The gauge shows paddle readiness until the third turn, then switches to the lift window.
Sneak-use with an empty hand to lift the hide near tick 160 (8 seconds), inside the marked interval. The recipe difficulty sets its width. An early or late lift, or too few clean stirs, loses 3 cells. Leaving a hide past tick 240 begins additional damage every 40 ticks. Work progresses only while the vat is loaded.
Scrape the flesh side
Place the soaked hide on the Fleshing Beam. Hold the Tanner’s Round Knife and aim at visible pale residue patches. Use as the moving marker crosses the marked interval. The 40-tick cycle repeats, so you can pause and wait for the next clean interval. Striking sound hide or missing the timing removes that actual cell. Removing all residue advances to stretching.
Tension and dry
Place the scraped hide on the rack. Hold the Leather Awl and use each corner to tighten its tie; sneak-use loosens it. Raise ties evenly to at least 2, with a spread no greater than 1. Pulling one corner too far tears fibres; tightening beyond 4 also tears the hide. Aim at the desired quadrant; the overlay identifies its tie. Empty-hand sneak-use retrieves the hide. Loosening corrects tension without additional tearing.
Drying needs 600 progress. Every 10 loaded ticks adds 8 normally, 12 in hot biomes, or 2 in rain. Drying advances only while the ties are balanced; adjusting away from balance pauses it. The hanging hide and tie positions reflect the saved work.
Finish and collect
Dress the dried hide with 1 honeycomb on the beam to reveal the chalk pattern. Aim at the leather near the middle and hold Use with each tool. The tool follows the outline while you keep contact.
| Tool | What to watch on the hide |
|---|---|
| Leather Shears | The ragged margin falls away along the chalk line, one edge at a time. |
| Skiving Knife | A narrow bevel appears along the newly cut edge. |
| Leather Awl | The point dips into the hide and leaves a row of dark stitch holes. |
| Waxed Thread & Needle | Pale stitches follow the punched seam around the panel. |
Each tool works 8 edges and costs 1 durability when its pass is complete. Release Use, look away or take the hide to another beam to pause. Completed edges stay with the hide. Resume by holding the indicated tool against the leather again.
Other tanners can watch the tool move and see each edge take shape. Only one tool can work the mounted hide at a time. Release it and another tanner can pick up where you stopped. The tanner who collects the leather receives the recipe credit.
Sneak-use with an empty hand to collect the finished leather or move unfinished work. Distance, logout and station changes do not refund already committed materials. Breaking a station drops its stored workpiece. The completion sound and particles accompany the finished hide; collection credits the tanning recipe once.
Data and related systems
Hides use isekaiexpansion:tanning recipes and agents use #isekaiexpansion:tanning_agents. Tanning recipe data documents difficulty, tone and grade limits. Finished leather becomes components for forgery; developers can read tanning runtime.